Категории

Signal Generator DIY Kit 1HZ-1MHZ DDS XR2206

Signal Generator DIY Kit 1HZ-1MHZ DDS XR2206

За этот товар не начисляются бонусные баллы.


Генератор сигналов (синус, треугольник, прямоугольник)

Подробнее ...

В наличии: 2

ROBO-210

9,90 €

  • Voltage Supply: 9-12V DC Input
  • Waveforms: Square, Sine & Triangle
  • Impedance: 600 Ohm + 10%
  • Frequency: 1Hz - 1MHz

SINE WAVE

  • Amplitude: 0 - 3V at 9V DC input
  • Distortion: Less than 1% (at 1kHz)
  • Flatness: +0.05dB 1Hz - 100kHz

SQUARE WAVE

  • Amplitude: 8V (no load) at 9V DC input
  • Rise Time: Less than 50ns (at 1kHz)
  • Fall Time: Less than 30ns (at 1kHz)
  • Symmetry: Less than 5% (at 1kHz)

TRIANGLE WAVE

  • Amplitude: 0 - 3V at 9V DC input
  • Linearity: Less than 1% (up to 100kHz) 10mA

The welding installation considerations, follow these steps:

  1. The components are welding the front board, from low to high principles, namely the first low welding components, such as, capacitor, resistor, diode, etc.
  2. Welding IC socket, terminal blocks, finally power socket, adjustable potentiometer.
  3. The back with a diagonal cutting pliers to cut short the pins as far as possible

Debugging steps:

  1. After completion of welding on IC, XR2206, pay attention to the direction of IC, insert the might damage the chip!
  2. Сheck the IC whether against, such as anti please timely correction.
  3. Insert the power supply, power supply for 5.5 * 2.1 port, inside outside is negative polarity. For 9-12 v power supply voltage. The waveform may not be stable for more than 12 v.

Using the step

   1. J1 jumper cap plug in, SIN/TRI blue terminals output sine wave (note J1, J2 can only insert one of)

   2. J2 jumper cap plug in, SIN/TRI blue terminals output triangular wave (note J1, J2 can only insert one of)

   3. SQU blue terminals output pulse

   4. AMP : Sine wave, triangle wave amplitude adjustment

   5. FINE : Frequency fine adjustment

   6. Coarse : Frequency of coarse adjustment

Написать собственный обзор

Signal Generator DIY Kit 1HZ-1MHZ DDS XR2206

Signal Generator DIY Kit 1HZ-1MHZ DDS XR2206

Генератор сигналов (синус, треугольник, прямоугольник)

Написать собственный обзор

26 других товаров в этой категории

RFID Arduino Starter KIT

RFID Arduino...

48,00 €

Digital FM5 конструктор

Digital FM5...

15,20 €

Digital Clock 5 SMD

Digital...

12,40 €

Digital LED Clock with termometr

Digital LED...

12,90 €

DIY ICL8038

DIY ICL8038

7,90 €

Basic Arduino Starter KIT2

Basic...

17,50 €

Ultimate RFID Master Starter Kit With UNO R3

Ultimate...

32,00 €

6DOF Aluminium Mechanical Robotic Arm

6DOF...

59,90 €

4WD Smart Robot Car Chassis Kits with Speed Encoder

4WD Smart...

32,00 €

2WD Smart Robot Car Chassis Kits

2WD Smart...

14,90 €

4 DOF Robot Arm with Servo Kit

4 DOF Robot...

35,50 €

2WD Smart Robot Car Chassis Kits (round)

2WD Smart...

19,50 €

Nano KIT - Temperatūra

Nano KIT -...

19,50 €

DIY Tank Chassis

DIY Tank...

26,00 €

DIY Tracking Robot Car With Reduction Motor

DIY Tracking...

9,50 €

DIY kit Digital clock C51

DIY kit...

12,50 €

TDA2822M Dual Channel Amplifier

TDA2822M...

4,90 €

DIY Car Kit Two-way Remote Control

DIY Car Kit...

9,90 €

Корзина  

Нет товаров

0,00 € Доставка:
0,00 € Итого, к оплате:

Оформить заказ

Контакты

Время работы: 10.00-13.00

тел.+371 27474705

E-Mail: robotop.lv@gmail.com

Адрес: Rīga, Limbažu iela 1/1


Весь товар, который можно положить в корзину

ЕСТЬ НА МЕСТЕ

Конструкторы