Categories

Signal Generator DIY Kit 1HZ-1MHZ DDS XR2206

Signal Generator DIY Kit 1HZ-1MHZ DDS XR2206

No reward points for this product.


Signal generator (sine, triangle, rectangle)

More details...

In stock: 1

00682

9,90 €

  • Voltage Supply: 9-12V DC Input
  • Waveforms: Square, Sine & Triangle
  • Impedance: 600 Ohm + 10%
  • Frequency: 1Hz - 1MHz

SINE WAVE

  • Amplitude: 0 - 3V at 9V DC input
  • Distortion: Less than 1% (at 1kHz)
  • Flatness: +0.05dB 1Hz - 100kHz

SQUARE WAVE

  • Amplitude: 8V (no load) at 9V DC input
  • Rise Time: Less than 50ns (at 1kHz)
  • Fall Time: Less than 30ns (at 1kHz)
  • Symmetry: Less than 5% (at 1kHz)

TRIANGLE WAVE

  • Amplitude: 0 - 3V at 9V DC input
  • Linearity: Less than 1% (up to 100kHz) 10mA

The welding installation considerations, follow these steps:

  1. The components are welding the front board, from low to high principles, namely the first low welding components, such as, capacitor, resistor, diode, etc.
  2. Welding IC socket, terminal blocks, finally power socket, adjustable potentiometer.
  3. The back with a diagonal cutting pliers to cut short the pins as far as possible

Debugging steps:

  1. After completion of welding on IC, XR2206, pay attention to the direction of IC, insert the might damage the chip!
  2. Сheck the IC whether against, such as anti please timely correction.
  3. Insert the power supply, power supply for 5.5 * 2.1 port, inside outside is negative polarity. For 9-12 v power supply voltage. The waveform may not be stable for more than 12 v.

Using the step

   1. J1 jumper cap plug in, SIN/TRI blue terminals output sine wave (note J1, J2 can only insert one of)

   2. J2 jumper cap plug in, SIN/TRI blue terminals output triangular wave (note J1, J2 can only insert one of)

   3. SQU blue terminals output pulse

   4. AMP : Sine wave, triangle wave amplitude adjustment

   5. FINE : Frequency fine adjustment

   6. Coarse : Frequency of coarse adjustment

Write your review

Signal Generator DIY Kit 1HZ-1MHZ DDS XR2206

Signal Generator DIY Kit 1HZ-1MHZ DDS XR2206

Signal generator (sine, triangle, rectangle)

Write your review

30 other products in the same category :

Digital oscillograph DSO138 (no SMD)

Digital...

29,00 €

Digital LED Clock with termometr

Digital LED...

12,90 €

Motor Smart Robot Car 4WD

Motor Smart...

68,00 €

DIY ICL8038

DIY ICL8038

7,90 €

Mini Wind Car DIY

Mini Wind...

7,80 €

Basic Arduino Starter KIT2

Basic...

14,00 €

6DOF Aluminium Mechanical Robotic Arm

6DOF...

59,90 €

4WD Smart Robot Car Chassis Kits with Speed Encoder

4WD Smart...

32,00 €

2WD Smart Robot Car Chassis Kits

2WD Smart...

14,90 €

4 DOF Robot Arm with Servo Kit

4 DOF Robot...

35,50 €

2WD Smart Robot Car Chassis Kits (round)

2WD Smart...

19,50 €

Nano KIT - Temperatūra

Nano KIT -...

19,50 €

DIY Tank Chassis

DIY Tank...

26,00 €

DIY Tracking Robot Car With Reduction Motor

DIY Tracking...

9,50 €

DIY kit Digital clock C51

DIY kit...

12,50 €

Digital oscillograph DSO062 DIY parts

Digital...

39,90 €

TDA2822M Dual Channel Amplifier

TDA2822M...

4,90 €

DIY Car Kit Two-way Remote Control

DIY Car Kit...

9,90 €

Power supply (1.25 V - 12.5 V) (1.5 W)

Power supply...

18,00 €

LM358 Breathing Lamp Electronics DIY Kit

LM358...

2,00 €

SMD Welding Practice Board Mini Version

SMD Welding...

3,00 €

Round Lucky Rotary Suite 

Round Lucky...

3,00 €

Melody Voice LED

Melody Voice...

3,00 €

Triode Transistor Multivibrator LED

Triode...

2,00 €

Water Flowing Light LED

Water...

3,00 €

Heart Circulation Module 18 Red LED 

Heart...

3,00 €

LM3915 10 segment Audio Level Indicator LED

LM3915 10...

4,00 €

Wireless sound transmission module

Wireless...

4,90 €

Digital Clock DIY - 03

Digital...

13,60 €

DIY Kit LM2596 Adjustable Voltage Stabilizer

DIY Kit...

3,80 €

Cart  

No products

0,00 € Shipping
0,00 € Total

Check out

Kontakti:

Darba laiks: 10.00-13.00 (on working days)

tālr.+371 27474705

E-Mail: robotop.lv@gmail.com

Adress: Rīga, Limbažu iela 1/1

New products

All new products