Categories

Intelligent Car Obstacle Avoidance Sensor Module For Arduino

Intelligent Car Obstacle Avoidance Sensor Module For Arduino

No reward points for this product.


The speed is quick, is suitable for smart car obstacle avoidance, black and white line tracking, prevent fall, counter products, line cutting, liquid level detection, etc.

More details...

In stock: 1

00113

4,60 €

Object is sensed output 0, output 1 is not sensitive to the time, directly with 3V and 5V microcontroller IO port connected.

   Sensing distance 2-40 cm, distance, good anti-jamming capability. (Note: The infrared sensor can not detect all objects get the same distance, objects of different colors of light reflectance of different objects closer darker black shorter distance detected, the sensor 2-40 cm is measured against the white wall of)

   Speed, suitable for smart car obstacle avoidance, black and white line tracking, anti-drop, product counters, cutting lines, liquid level detection.

   This sensor is made with black and white lines tracing the car ran without black line on white paper, available in concrete The yellow complex environment such as the black line patrol track. As long as the black line around the slightly lighter color than black can, eliminating the traditional moves, so that environmental layout easier.

   The sensor 3 to 6V supply, wide range, suitable for 3V and 5V MCU system.

   With Enable, EN terminal is equal to "1" when the sensor does not work, equal to "0" when working. Jump on the sensor end cap long after the EN grounding plug (EN long as "0"). To use the EN pin when the jumper cap is removed.

   Frequency adjustment potentiometer is used to adjust the carrier frequency of the infrared emission tube, because the integration receiver 38KHZ in particular when the carrier frequency is the most sensitive. The 502 resistor clockwise transferred do (that is, the launch tube at maximum brightness), and then at a white wall tone 103 resistance, has been transferred to the sensing distance is the farthest so far so that the sensor will work in the best state

   Working voltage: DC 3.3V-5V

   Working current: 20mA

   Working temperature: -10degree+50degree

   Detection distance : 2-40cm

   IO interface: 4 line (-/+/S/EN)

   Output signal: TTL Level

   Adjusting mode: Multi resistance regulation

   Effective angle: 35°

   Size: 4.5x1.1cm(approx)

   Here we use the obstacle avoidance module and digital 13 interface with LED to build a simple circuit, making the obstacle avoidance warning light, accessing the avoidance sensor to digital 3 interface, when the obstacle avoidance sensor senses the signal, LED light, otherwise off.

   Program code:

   int Led=13;//define LED interface

   int buttonpin=3; //define obstacle avoidance interface

   int val;//define Digital variable val

   void setup()

   {

   pinMode(Led,OUTPUT);//define LED is output interface

   pinMode(buttonpin,INPUT);//define obstacle avoidance is output interface

   }

   void loop()

   {

   val=digitalRead(buttonpin);//reading the value from 3 digital interface to val

   if(val==HIGH)//when the obstacle avoidance sensor senses the signal, LED flash

   {

   digitalWrite(Led,HIGH);

   }

   else

   {

   digitalWrite(Led,LOW);

   }

   }

  • Operating Voltage: 2.7-5.5V

Write your review

Intelligent Car Obstacle Avoidance Sensor Module For Arduino

Intelligent Car Obstacle Avoidance Sensor Module For Arduino

The speed is quick, is suitable for smart car obstacle avoidance, black and white line tracking, prevent fall, counter products, line cutting, liquid level detection, etc.

Write your review

30 other products in the same category :

Beat sensor module - KY-031

Beat sensor...

1,50 €

Vibration switch module

Vibration...

1,50 €

Tilt switch module

Tilt switch...

1,50 €

Mercury open optical module

Mercury open...

1,50 €

JoyStick (9 pin)

JoyStick (9...

3,90 €

TCRT5000 MOD.3

TCRT5000 MOD.3

3,50 €

Rotary encoders

Rotary encoders

3,00 €

HC-SR04 Ultrasonic Distance Measuring Sensor Module for Arduino

HC-SR04...

3,50 €

Light Cup

Light Cup

2,10 €

Triple Axis Compass Magnetometer Sensor (HMC5883L)

Triple Axis...

3,00 €

US-05 Ultrasonic Distance Measuring Sensor Module for Arduino

US-05...

3,00 €

SRF05 Ultrasonic Distance Measuring Sensor Module for Arduino

SRF05...

4,50 €

GY-521 - 3 Axis Analog Gyroscope + Accelerometer MPU-6050

GY-521 - 3...

3,20 €

TCRT5000 MOD.2

TCRT5000 MOD.2

3,50 €

TCRT5000 Sensor tracking (4 channel)

TCRT5000...

5,60 €

GY-50 Three Axis Digital Rate Gyroscope L3G4200D

GY-50 Three...

5,30 €

TCRT5000 MOD.1

TCRT5000 MOD.1

3,50 €

SW-420 Vibration Sensor

SW-420...

1,90 €

3-way tracking module

3-way...

4,70 €

5-way tracking module

5-way...

6,70 €

IR Infrared Slotted Optical Speed Measuring Sensor

IR Infrared...

1,90 €

VL53L0X World smallest Time-o f-Flight (ToF) laser ranging sensor

VL53L0X...

9,20 €

Pressure sensor FSR402 0.5"

Pressure...

12,90 €

SW520D angle sensor module

SW520D angle...

1,90 €

Original Gaode Inductive Proximity Sensor LJ12A3-4-Z/BX

Original...

4,50 €

MPU-9250 Gyroscope+Accelerometer+Magnetometer

MPU-9250...

6,80 €

OptoCoupler - photo interrupter module

OptoCoupler...

2,30 €

Infrared distance sensor GP2Y0A41SK0F 4-30cm

Infrared...

8,90 €

VL53L0X Time-of-Flight (ToF) Laser Ranging Sensor

VL53L0X...

8,80 €

OptoCoupler - photo interrupter module 1

OptoCoupler...

1,80 €

Cart  

No products

0,00 € Shipping
0,00 € Total

Check out

Kontakti:

Darba laiks: 10.00-13.00 (on working days)

tālr.+371 27474705

E-Mail: robotop.lv@gmail.com

Adress: Rīga, Limbažu iela 1/1

New products

All new products