Categories

Dear customers!

Currently, product delivery is only available via OMNIVA.
We apologize for any inconvenience caused.

GY-9960LLC APDS-9960 RGB and Gesture Sensor

GY-9960LLC APDS-9960 RGB and Gesture Sensor

No reward points for this product.


Gesture, light, color and proximity sensor

More details...

In stock: 2

00825

4,90 €

Description:  Sensor for gestures, light, color and approximation APDS-9960

APDS9960 sensor  - is able to determine the level of illumination in Lux (both general and for three channels of the spectrum - red, green, blue), the approach of objects (obstacles) and gestures (movement of objects to the left, right, up, down, to the sensor and from ).

General information:

The module is based on the eponymous sensor APDS9960, which is composed of 4 photodiode for detecting gestures 3 photodiode responsive to the different spectra to determine the colors, one photodiode total light, UV and IR filters, amplifiers with programmable gain, MC, ALU, ADC, RAM, I2C bus controller with slave address 0x39 and many additional blocks. The results of illumination in Lux are derived using an empirical formula for approximating the reaction of the human eye.

Gestures:

  • The sensor APDS9960 is able to respond to the following gestures:
  • UP  - Hand movement in front of the sensor.  FORWARD  or  UP  (depends on the position of the sensor in the space).
  • DOWN  - Movement of the hand before the sensor  BACK  or  DOWN  (depends on the position of the sensor in the space).
  • LEFT  - Move the hand in front of the sensor  LEFT .
  • RIGHT  - Move the hand in front of the RIGHT sensor  .
  • NEAR  - Approaching the hand  To the  sensor. 
    Smoothly zoom in hand to the top of the sensor at a distance of ≈ 1-5 cm., Hold it for at least 1 second, and quickly move in any direction.
  • FAR  Removing hands  FROM  sensor. 
    Quickly move your hand to the sensor from any direction, for a distance of ≈ 1-5 cm, hold it for at least 1 second and smoothly remove from the sensor upwards.
  • NONE  The sensor detected movement, but could not recognize it.

Connection:

The sensor APDS-9960 logic and power only 3.3 V!

The SDA and SCL module leads are connected to the I2C Arduino hardware bus. If your Arduino has 5V logic, the SDA and SCL pins are connected via a 3.3V to 5V bi-directional level converter.

The conclusions GND, VCC are the power outputs (VCC output - the module power is +3.3 V).

The INT output of the module is the output of the interrupt (active level - logical "0") which, depending on the selected operating mode, can respond to brightness, object detection, actions, etc. You can not use this conclusion (constantly polling the module), you can use it for its intended purpose (connect to the Arduino output supporting an external interrupt) and interrogate the module only by external interruption, and you can connect to it a normal LED that will signal that the module has responded to some action or event.

Specification:

  • Input power supply voltage (VCC): 2.4 ... 3.6 VDC (nominally 3.3 V).
  • Current consumed by the module:
    • In the mode of measuring the illumination level: up to 250 μA.
    • In the approximation mode: up to 790 μA.
    • In the mode of detection of gestures: up to 790 mkA.
    • Standby time: up to 38 μA.
    • In sleep mode: up to 10 μA.
  • I2C bus clock frequency: up to 400 kHz.
  • The address of the module on the I2C bus is 0x39.
  • Operating temperature: -30 ... +85 ° С.
  • Storage temperature: -40 ... +85 ° С.
  • Dimensions: 15x20 mm
  • Weight: 3 gr.

Write your review

GY-9960LLC APDS-9960 RGB and Gesture Sensor

GY-9960LLC APDS-9960 RGB and Gesture Sensor

Gesture, light, color and proximity sensor

Write your review

30 other products in the same category :

37 in 1 Sensors KIT for Arduino

37 in 1...

20,00 €

Snow/Raindrops Detection Sensor For Arduino

Snow/Raindro...

2,00 €

SRF05 Ultrasonic Distance Measuring Sensor Module for Arduino

SRF05...

4,50 €

IR Wireless Remote Control Module Kits

IR Wireless...

4,50 €

GY-521 - 3 Axis Analog Gyroscope + Accelerometer MPU-6050

GY-521 - 3...

3,20 €

RC522 RFID with card and key

RC522 RFID...

5,50 €

HX1838 Remote Control RC21 (3 in 1)

HX1838...

4,50 €

37 in 1 Sensors KIT for Arduino with BOX

37 in 1...

26,00 €

1 way Capacitive Touch Switch Module with LED TTP223B

1 way...

1,30 €

8 way Capacitive Touch Switch Module with LED TTP226

8 way...

2,80 €

16 way Capacitive Touch Switch Module with LED TTP229

16 way...

3,20 €

4 way Capacitive Touch Switch Module with LED TTP224

4 way...

1,90 €

DHT11 Temp and humidity LED

DHT11 Temp...

3,80 €

DHT21 AM2301

DHT21 AM2301

5,40 €

HC-SR501

HC-SR501

2,50 €

MQ-6 Gas Sensor

MQ-6 Gas Sensor

8,90 €

MQ-2 Smoke Gas Sensor

MQ-2 Smoke...

5,40 €

MQ-135 Air Quallty Sensor

MQ-135 Air...

4,50 €

MQ-5 Methane Gas Sensor

MQ-5 Methane...

4,60 €

MQ-4 Methane Gas Sensor

MQ-4 Methane...

3,80 €

MQ-3 Alcohol Ethanol Sensor

MQ-3 Alcohol...

3,20 €

BMP180

BMP180

4,50 €

MQ-7 CO sensor

MQ-7 CO sensor

4,20 €

TCRT5000 MOD.2

TCRT5000 MOD.2

3,50 €

TCRT5000 Sensor tracking (4 channel)

TCRT5000...

5,60 €

GY-50 Three Axis Digital Rate Gyroscope L3G4200D

GY-50 Three...

5,30 €

BH1750FVI-A

BH1750FVI-A

2,80 €

PCF8591 AD / DA converter

PCF8591 AD /...

2,50 €

TCRT5000 MOD.1

TCRT5000 MOD.1

3,50 €

Flame sensor

Flame sensor

2,90 €

Cart  

No products

0,00 € Shipping
0,00 € Total

Check out

Kontakti:

Darba laiks: 10.00-13.00 (on working days)

tālr.+371 27474705

E-Mail: robotop.lv@gmail.com

Adress: Rīga, Limbažu iela 1/1