LM2596 DC-DC 30V 4A LED
LM2596 DC-DC 30V 4A LED
LM2596 DC-DC 30V 4A LED
LM2596 DC-DC 30V 4A LED
LM2596 DC-DC 30V 4A LED
LM2596 DC-DC 30V 4A LED

LM2596 DC-DC 30V 4A LED

Sprieguma pārveidotājs DC-DC 7-35V to 1.35-30V

00854
Nav noliktavā
3,40 €


 
1.Fixed turn the lamp current to 0.1 times the value of the constant current (charge when used to identify whether the battery is full);
2. Increased input reverse polarity protection diode;
3. Increase the output of a backflow preventing diode to prevent when the electricity to charge the battery back in;
4. Using dedicated reference IC, and high-precision sampling resistor, so that the constant current is more stable, (20 degrees to 100 degrees, the constant current 1A, when the temperature drift of less than 1%).
 
  • Particularly suitable for LED driver
  • High-power LED constant current drive
  • Lithium battery charger (including ferroelectric)
  • 4V, 6V, 12V, 14V, 24V battery charger
  • Nickel cadmium, nickel metal hydride battery pack charger
  • Solar panels and wind turbines
 
 
Specifications:
 
  • Input Voltage: 5-35V
  • Output Voltage: Continuously adjustable from 1.25 V to 30V
  • Rated Output Current: 3A
  • Max. Output Current:4A(more than 15W, preferably with a heat sink)
  • Size (L x W x H): Approx. 1.9 x 0.95 x 0.5 inch / 4.8 x 2.4 x1.3cm
  • Indicator Light
  • Constant current indicator(red)
  • Charging indicator(red)
  • Charged full (green)
 
Battery use:
 
l Make sure of the voltage and current of the battery you need to charge
l Adjust the constant voltage potentiometer to make the output voltage same to the charge voltage
l Potentiometer Adjustment Direction: Clockwise (increase), counterclockwise (decrease)
Use the multimeter in 10A current scale to measure output short-circuit current, and adjust the current potentiometer to make sure the output current to the expected charging current value
l The charge current of transfer lamp is default 0.1 times of the charging current (constant current value)
l Connected to the battery and try to charging (for previous 5 steps, module input terminal is connected to power source, output load is NOT connected to batteries)
 
 
LED Constant Current Driver Use:
 
l Make sure operating current and Max operating Voltage of the LED you need to drive
l Adjust the constant voltage potentiometer to make sure the output Voltage is up to LED Max operating Voltage
Use the multimeter in 10A current scale to measure output short-circuit current, and adjust the current potentiometer
l to make sure the output current to the expected LED operating current
l Join LED, test (For the above 3 steps, module input terminal is connected to power source, output load is NOT connected to LED)
Nav atsauksmju

16 citi produkti tajā pašā kategorijā:

Produkts ir pievienots vēlmju sarakstam
Produkts pievienots salīdzināšanai.

Mūsu interneta vietnē tiek izmantoti sīkfaili. Sīkfaili palīdz nodrošināt pienācīgu vietnes darbību un tās pilnveidošanu, tāpēc obligātie sīkfaili (tehniskie, funkcionālie un analītiskie) tiek instalēti automātiski. Lai individualizētu jūsu sērfošanas pieredzi un sniegtu piedāvājumus, kuri būtu aktuāli tieši jums, tīmekļa vietnē tiek izmantoti arī mērķa sīkfaili. Nospiežot “piekrītu”, jūs piekrītat mērķa sīkfailu instalēšanai un izmantošanai. Savu piekrišanu varēsiet atsaukt jebkurā laikā, nomainot sava interneta pārlūka iestatījumus un izdzēšot ierakstītos sīkfailus. Vairāk informācijas – sīkfailu politikā