Signal Generator DIY Kit 1HZ-1MHZ DDS XR2206
Signal Generator DIY Kit 1HZ-1MHZ DDS XR2206
Signal Generator DIY Kit 1HZ-1MHZ DDS XR2206
Signal Generator DIY Kit 1HZ-1MHZ DDS XR2206
Signal Generator DIY Kit 1HZ-1MHZ DDS XR2206
Signal Generator DIY Kit 1HZ-1MHZ DDS XR2206
Signal Generator DIY Kit 1HZ-1MHZ DDS XR2206
Signal Generator DIY Kit 1HZ-1MHZ DDS XR2206
Signal Generator DIY Kit 1HZ-1MHZ DDS XR2206
Signal Generator DIY Kit 1HZ-1MHZ DDS XR2206
Signal Generator DIY Kit 1HZ-1MHZ DDS XR2206
Signal Generator DIY Kit 1HZ-1MHZ DDS XR2206

Signal Generator DIY Kit 1HZ-1MHZ DDS XR2206

Signālu ģenerators (sinuss, trīsstūri, taisnstūri)

00682
2
9,90 €

 
  • Voltage Supply: 9-12V DC Input
  • Waveforms: Square, Sine & Triangle
  • Impedance: 600 Ohm + 10%
  • Frequency: 1Hz - 1MHz

SINE WAVE

  • Amplitude: 0 - 3V at 9V DC input
  • Distortion: Less than 1% (at 1kHz)
  • Flatness: +0.05dB 1Hz - 100kHz

SQUARE WAVE

  • Amplitude: 8V (no load) at 9V DC input
  • Rise Time: Less than 50ns (at 1kHz)
  • Fall Time: Less than 30ns (at 1kHz)
  • Symmetry: Less than 5% (at 1kHz)

TRIANGLE WAVE

  • Amplitude: 0 - 3V at 9V DC input
  • Linearity: Less than 1% (up to 100kHz) 10mA

The welding installation considerations, follow these steps:

  1. The components are welding the front board, from low to high principles, namely the first low welding components, such as, capacitor, resistor, diode, etc.
  2. Welding IC socket, terminal blocks, finally power socket, adjustable potentiometer.
  3. The back with a diagonal cutting pliers to cut short the pins as far as possible

Debugging steps:

  1. After completion of welding on IC, XR2206, pay attention to the direction of IC, insert the might damage the chip!
  2. Сheck the IC whether against, such as anti please timely correction.
  3. Insert the power supply, power supply for 5.5 * 2.1 port, inside outside is negative polarity. For 9-12 v power supply voltage. The waveform may not be stable for more than 12 v.

Using the step

   1. J1 jumper cap plug in, SIN/TRI blue terminals output sine wave (note J1, J2 can only insert one of)

   2. J2 jumper cap plug in, SIN/TRI blue terminals output triangular wave (note J1, J2 can only insert one of)

   3. SQU blue terminals output pulse

   4. AMP : Sine wave, triangle wave amplitude adjustment

   5. FINE : Frequency fine adjustment

   6. Coarse : Frequency of coarse adjustment

2 vienības:
Nav atsauksmju

16 citi produkti tajā pašā kategorijā:

Produkts ir pievienots vēlmju sarakstam
Produkts pievienots salīdzināšanai.

Mūsu interneta vietnē tiek izmantoti sīkfaili. Sīkfaili palīdz nodrošināt pienācīgu vietnes darbību un tās pilnveidošanu, tāpēc obligātie sīkfaili (tehniskie, funkcionālie un analītiskie) tiek instalēti automātiski. Lai individualizētu jūsu sērfošanas pieredzi un sniegtu piedāvājumus, kuri būtu aktuāli tieši jums, tīmekļa vietnē tiek izmantoti arī mērķa sīkfaili. Nospiežot “piekrītu”, jūs piekrītat mērķa sīkfailu instalēšanai un izmantošanai. Savu piekrišanu varēsiet atsaukt jebkurā laikā, nomainot sava interneta pārlūka iestatījumus un izdzēšot ierakstītos sīkfailus. Vairāk informācijas – sīkfailu politikā