MCP23017 16-Bit I/O Expander 10Mhz
MCP23017 16-Bit I/O Expander 10Mhz
MCP23017 16-Bit I/O Expander 10Mhz
MCP23017 16-Bit I/O Expander 10Mhz
MCP23017 16-Bit I/O Expander 10Mhz
MCP23017 16-Bit I/O Expander 10Mhz

MCP23017 16-Bit I/O Expander 10Mhz

Portu paplašinātājs

00876
2 vienības:
4,50 €

 

Description:

This module is the 16 way IO extension module of the 12C interface, and built in the MCP23017 chip of MicroChip. The function of the chip is complete. Each IO can be arbitrarily configured as input or output, and a pull up resistor can be set, and the interrupt function can be enabled for the IO configured as input. The IO interface has a strong driving capacity, and the current and current can reach 25mA.
      MCP23017 is a high-speed IIC interface. It supports the IIC frequency of 100KHz, 400KHz and 1.7MHz. The chip has 3 address pins, which can be set up for 8 different addresses. So 8 modules can be connected through two IIC buses to achieve up to 128 IO extensions.
      This module is flexible in configuration and strong in driving ability. There are many parallel connections.

Parameters:

No.

Parameter

Value

1

Operating voltage

3.0V-5.5V

2

Drive chip

MCP23017

3

Number of IO

16 (input, output, interruption)

4

Drive power supply

25mA1

5

12C frequency

100KHz, 400KHz, 1..7MHz

6

working temperature

-40 Celsius -125  Celsius

7

Chip level

Industrial grade

8

Parallel multiple

Up to 8

9

Driver

51 and Arduino

10

Module size

65mm*19mm

 

Pin description:

No.

Pin

Function

Remark

1

VCC

Power source input

3.0V-5.5V

2

GND

Power negative electrode

0V

3

SCL

12C clock line

SCL connecting single chip IO pin or MCU 12C interface

4

SDA

12C data line

SDA connecting single chip IO pin or MCU 12C interface

5

RST

Chip reduction

Low level effective, connecting MCU IO pin or unconnected

6

ITA

GPIOA port interrupt output

Connect MCU IO pin, without connection when interruption

7

ITB

GPIOB port interrupt output

Connect MCU IO pin, without connection when interruption

Description:

16-Bit Remote Bidirectional I/O Port:
- I/O pins default to input
• High-Speed I2C Interface (MCP23017):
- 100kHz
- 400kHz
- 1.7MHz
• High-Speed SPI Interface (MCP23S17):
- 10 MHz (maximum)
• Three Hardware Address Pins to Allow Up to
Eight Devices On the Bus
• Configurable Interrupt Output Pins:
- Configurable as active-high, active-low or
open-drain
• INTA and INTB Can Be Configured to Operate
Independently or Together
• Configurable Interrupt Source:
- Interrupt-on-change from configured register
defaults or pin changes
• Polarity Inversion Register to Configure the
Polarity of the Input Port Data
• External Reset Input
• Low Standby Current: 1 μA (max.)
• Operating Voltage:
- 1.8V to 5.5V @ -40°C to +85°C
- 2.7V to 5.5V @ -40°C to +85°C
- 4.5V to 5.5V @ -40°C to +125°C  

2 vienības:
No reviews

16 citi produkti tajā pašā kategorijā:

Produkts ir pievienots vēlmju sarakstam
Produkts pievienots salīdzināšanai.

Mūsu interneta vietnē tiek izmantoti sīkfaili. Sīkfaili palīdz nodrošināt pienācīgu vietnes darbību un tās pilnveidošanu, tāpēc obligātie sīkfaili (tehniskie, funkcionālie un analītiskie) tiek instalēti automātiski. Lai individualizētu jūsu sērfošanas pieredzi un sniegtu piedāvājumus, kuri būtu aktuāli tieši jums, tīmekļa vietnē tiek izmantoti arī mērķa sīkfaili. Nospiežot “piekrītu”, jūs piekrītat mērķa sīkfailu instalēšanai un izmantošanai. Savu piekrišanu varēsiet atsaukt jebkurā laikā, nomainot sava interneta pārlūka iestatījumus un izdzēšot ierakstītos sīkfailus. Vairāk informācijas – sīkfailu politikā